During the course of filming we realised that we could most likely get some good looking tracking shots for use in our New Wave films so we decided to film from a car window whilst it was moving around various locations, although this presented a problem as we would need to first alter the cameras shutter speed before filming otherwise the footage would be too out of focus due to motion blur, so the first thing that was needed was to alter the cameras settings.
This footage shows a tracking shot from a moving car with the shutter speed set at 1/100s which is too slow as while the car is moving everything becomes distorted and blurred, the aperture was set at f/22 while the ISO was set at 1200 so everything was in focus, and the shutter speed was set at a speed that would allow an appropriate amount of light into the camera, however this caused the camera to capture the car movement at a slower rate causing this motion blur to occur.
This footage however shows the movement from the car more clearly, this is due to the cameras shutter speed being changed to a quicker rate of about 1/500s which captured the movement more clearly, also the other settings had not been altered so the ISO was still at about 1200, and the aperture at f/22 so everything was captured in focus and enough light was able to be absorbed by the camera to provide a bright look o the footage.
This footage could also be seen as new wave since it is using innovative camera movements to establish a tracking shot, using a cheap inexpensive and moderately effective method that requires almost no budget and it does show the local area where most of our footage takes place.
Showing posts with label Unit 30: Camera and Lighting Techniques. Show all posts
Showing posts with label Unit 30: Camera and Lighting Techniques. Show all posts
Tuesday, 20 November 2012
Lighting Techniques: Low Key Lighting
Low Key lighting is used and is most effective when only a single light source is present within a shot be it either overhead, eye level or at a low angle, it can create different effects on the subject. One of its main aspects is that the light casts a great deal of shadow across the subject, which can generate different connotations of the subject, such as the light source being on one side of them at eye level, casting half of their features in shadow would make them appear mysterious or intimidating. Low key lighting is often used in Noir films but also in New Wave films because as it only uses one light source it is a cost effective way of lighting a scene and effects such as Rembrandt or Edge lighting can be applied using only one small light source.
The pieces of footage below are examples of our use of low key lighting.
Continuity 2 from Lewis Mercer on Vimeo.
This footage uses low key light as only a small light source is used to highlight the subject, the light source itself was in fact the light from a mobile phone which only created a small amount of light, a wide aperture of f/2.8 was used with an aperture of at least 800 since we were using a very small light source we didn't want the footage to be underexposed, this footage falls into conventions of new wave because it is using a very cheap form of lighting which is inventive as due to the small area we could most likely not accommodate large studio lights.
Edge light ex from Lewis Mercer on Vimeo.
This footage on the other hand uses a large light source but is very limited as we controlled the amount of light using "barn doors" attached to the light so we could decrease or increase the amount of light that hit the subject, This footage was shot using an ISO of 800 and an aperture of at least f/16 as we were using a larger light source so more light would be entering the cameras sensors, this form of lighting known as Edge lighting was used in New Wave films as a cheap way of creating studio like light effects on a budget as it is a technique that requires only one light source which would be appropriate to a filmmaker with little or no budget.
The pieces of footage below are examples of our use of low key lighting.
Continuity 2 from Lewis Mercer on Vimeo.
This footage uses low key light as only a small light source is used to highlight the subject, the light source itself was in fact the light from a mobile phone which only created a small amount of light, a wide aperture of f/2.8 was used with an aperture of at least 800 since we were using a very small light source we didn't want the footage to be underexposed, this footage falls into conventions of new wave because it is using a very cheap form of lighting which is inventive as due to the small area we could most likely not accommodate large studio lights.
Edge light ex from Lewis Mercer on Vimeo.
This footage on the other hand uses a large light source but is very limited as we controlled the amount of light using "barn doors" attached to the light so we could decrease or increase the amount of light that hit the subject, This footage was shot using an ISO of 800 and an aperture of at least f/16 as we were using a larger light source so more light would be entering the cameras sensors, this form of lighting known as Edge lighting was used in New Wave films as a cheap way of creating studio like light effects on a budget as it is a technique that requires only one light source which would be appropriate to a filmmaker with little or no budget.
Camera Tech: Shutter Speed
Shutter speed is the speed in which the lens gate on a camera opens and closes during a shot or whilst filming, on DSLR cameras this speed can be manually adjusted to create different effects. Shutter speed effects the amount of time the camera sensor is exposed to light and can also affect how movement appears in the image. For example a slow shutter speed would mean the camera lens gate is left open for longer periods of time, exposing the cameras light sensor for longer and capturing movement at a slower rate, whereas a fast shutter speed would rapidly open and close the cameras lens gate, limiting the amount of time the sensors are exposed to light and capturing quick movement instantly.
Shutter speed is measured in direct relation to the cameras Aperture settings at a 2:1 scale e.g. an aperture of f/2.8 is equal to a shutter speed of 1/1000s so the wider the aperture the faster the shutter speed this is to ensure that the camera is exposed to the correct amount of light to produce the image and is not overexposed, the highest shutter speed for a typical DSLR camera today is roughly 1/1600s with the lowest being 1/10s. Below is an example of how shutter speed can effect an image.
Shutter speed is measured in direct relation to the cameras Aperture settings at a 2:1 scale e.g. an aperture of f/2.8 is equal to a shutter speed of 1/1000s so the wider the aperture the faster the shutter speed this is to ensure that the camera is exposed to the correct amount of light to produce the image and is not overexposed, the highest shutter speed for a typical DSLR camera today is roughly 1/1600s with the lowest being 1/10s. Below is an example of how shutter speed can effect an image.
The first image is taken with a very high shutter speed to quickly capture the movement of the object and the far right image is taken with a slow shutter speed which is exposed longer and thus captures more of the objects movement which blends it together and creates a blur of motion.
While being used in tandem with other settings such as Aperture if the aperture is set on a low setting and the aperture is very wide then a quicker shutter speed would be required otherwise it would be too overexposed to light, this is also true if a high ISO is being used as the cameras sensor would be more sensitive to light so a faster shutter speed would ensure that the camera is not exposed for too long, if the aperture was a very high setting and it was a very narrow depth of field with a low ISO a slower shutter speed would be used otherwise the image would be underexposed and would appear very dark.
Camera Tech: I.S.O
ISO is the measure of how sensitive the camera becomes to incoming light and effects how exposed the image or film is light. An example would be using a high ISO is areas with limited light sources or whilst filming at night and a low ISO for areas that are well lit such as a high volume of natural light, however a high ISO also increases the amount of image noise which distorts the image by giving it a very grainy, static appearance, so a low ISO is often the best option, especially when used with either a low shutter speed or wide aperture as using a high ISO in this circumstance would overexpose the image.
Most digital DSLR cameras have the option to alter the ISO manually depending on the situation you are shooting in and generally have ISO values that range from 100 to 3200, 100 ISO in the right light conditions would give a very crisp clear shot whereas an ISO of 3200 would dramatically increase the film grain on the image. Below is an example of how ISO affects an image.
The image on the left uses an ISO of 100 so the shot is very crisp and clear whereas the image on the right is shot using an ISO of 3200 which has increased the amount of grain on the image, distorting it slightly. Generally a low ISO would be used for high density light conditions however it can also be used in tandem with a wide aperture or a low shutter speed to limit the amount of film grain on the image while still being brightly lit as the wide aperture would allow more light into the camera so a low ISO making the light sensor less sensitive would be appropriate.
Most digital DSLR cameras have the option to alter the ISO manually depending on the situation you are shooting in and generally have ISO values that range from 100 to 3200, 100 ISO in the right light conditions would give a very crisp clear shot whereas an ISO of 3200 would dramatically increase the film grain on the image. Below is an example of how ISO affects an image.
The image on the left uses an ISO of 100 so the shot is very crisp and clear whereas the image on the right is shot using an ISO of 3200 which has increased the amount of grain on the image, distorting it slightly. Generally a low ISO would be used for high density light conditions however it can also be used in tandem with a wide aperture or a low shutter speed to limit the amount of film grain on the image while still being brightly lit as the wide aperture would allow more light into the camera so a low ISO making the light sensor less sensitive would be appropriate.
Camera Tech: White Balance
White balance is how the camera adjusts the intensity of primary colours, to correct the colour scale in an image by keeping neutral colours neutral. This means that by adjusting white balance it ensures that objects which appear white in reality are rendered as white in the image and removes colour casts that may occur that would give the image a blue,orange or green tint to it. The adjustment of white balance on a camera means it has to discern the "colour temperature" of a light source which refers to relative "coolness" or "warmth" of neutral white light which can improve the image taken on a camera under different light conditions.
The following table is a guide on the correlated colour temperature of common light sources.
White balance from Lewis Mercer on Vimeo.
The first piece of footage shows how the white balance as it was by default which in the lighting conditions of the location we were in cast an orange tinted glow over the images which was not how the colours appeared in reality, the second piece of footage shows the effects of the white balance being changed to suit the lighting conditions which made the images appear much clearer, the whites in the images also appear as they appear in reality which makes the footage look brighter by comparison.
The following table is a guide on the correlated colour temperature of common light sources.
| Color Temperature | Light Source |
| 1000-2000 K | Candlelight |
| 2500-3500 K | Tungsten Bulb (household variety) |
| 3000-4000 K | Sunrise/Sunset (clear sky) |
| 4000-5000 K | Fluorescent Lamps |
| 5000-5500 K | Electronic Flash |
| 5000-6500 K | Daylight with Clear Sky (sun overhead) |
| 6500-8000 K | Moderately Overcast Sky |
| 9000-10000 K | Shade or Heavily Overcast Sky |
The following footage shows how the white balance needs to be adjusted in certain light conditions in order to render colours correctly within the image as they would appear in reality.
White balance from Lewis Mercer on Vimeo.
The first piece of footage shows how the white balance as it was by default which in the lighting conditions of the location we were in cast an orange tinted glow over the images which was not how the colours appeared in reality, the second piece of footage shows the effects of the white balance being changed to suit the lighting conditions which made the images appear much clearer, the whites in the images also appear as they appear in reality which makes the footage look brighter by comparison.
Innovative Camera Movements
One aspect of New Wave films that made them separate from mainstream cinema during their time was with the use of innovative and creative camera angles and movements using anything they could to move the camera in different ways, such as in Godard's "Breathless" where the camera is placed on the top of an escalator to film the woman as she ascends. The use of innovative camera movements can alter the way in which an audience views a film.
Spinning Shot test 1 from Lewis Mercer on Vimeo.
For this shot we tried to use a local parks "merry go round" as a way of making the camera spin whilst a subject was in the foreground, giving the appearance that the background was moving while the subject remained motionless. We used a setting of Aperture of f/22 to make the subject in the foreground in sharp focus however the background became blurry and out of focus which would be due to the spinning of the camera, we also used an ISO of between 600-800 so that the footage would be brighter as on the day we filmed this it was very dark and overcast.
escalator footage from Lewis Mercer on Vimeo.
This footage was done to try and imitate the scene from Godards "Breathless" where a woman ascends on an escalator and the camera is placed in front of her during the ride upward as if the camera is moving with her as an innovative and cheap alternative to a tracking shot, also we tried to shoot the footage in black and white to further imitate the scene from Godards film. This footage was done to be New Wave as it was using a single camera being handheld in a public area, and also we have no budget to film with so innovative use of the camera is needed.
This is a few examples of how we have tried to use innovative camera movement within our process of filming.
Spinning Shot test 1 from Lewis Mercer on Vimeo.
For this shot we tried to use a local parks "merry go round" as a way of making the camera spin whilst a subject was in the foreground, giving the appearance that the background was moving while the subject remained motionless. We used a setting of Aperture of f/22 to make the subject in the foreground in sharp focus however the background became blurry and out of focus which would be due to the spinning of the camera, we also used an ISO of between 600-800 so that the footage would be brighter as on the day we filmed this it was very dark and overcast.
escalator footage from Lewis Mercer on Vimeo.
This footage was done to try and imitate the scene from Godards "Breathless" where a woman ascends on an escalator and the camera is placed in front of her during the ride upward as if the camera is moving with her as an innovative and cheap alternative to a tracking shot, also we tried to shoot the footage in black and white to further imitate the scene from Godards film. This footage was done to be New Wave as it was using a single camera being handheld in a public area, and also we have no budget to film with so innovative use of the camera is needed.
Filming in Coloured Environments
During filming there is something that needs to be considered, something that can define a shot and make it stand out and that is the kinds of colours used. Colour can provide subjective meanings and can have multiple connotations of different things within a shot, e.g. red meaning danger or white meaning innocence etc. Colour within a shot can help set the mood and atmosphere of a scene such as bright colours being used to suggest an upbeat positive feel, and this can provoke reactions from audiences.
We tried to film in various different coloured environments to see how colours may change depending on the type of background they are in and what effects they may have. This is a short montage of a few locations that use bright colours in the background or to purposely draw people towards them, such as advertisements or sweets.
Color footage from Lewis Mercer on Vimeo.
The coloured buildings on the street seem to give the area a sense of variety and it makes them all look quite inviting, as while they seem like old styled buildings due to the bright colours they are not too imposing. While the brightly packaged sweets and chocolates seem to try and draw you towards them as an incentive to buy them which shows how colours can affect what people may buy, this is also the case with the small cafe as with it being coloured very brightly it looks like it would have a rather positive atmosphere inside, inviting people in.
OH&S: Occupational Health and Safety
As this was a new area we were filming in there would need to be some precautions as to how we were going to film and where as the area was unfamiliar to us we would need to take extra care when travelling to a location. In this instance it was a rather busy street so we would need to be careful not to get in peoples way or have any of the equipment damaged. some of the risks involved included:
We tried to film in various different coloured environments to see how colours may change depending on the type of background they are in and what effects they may have. This is a short montage of a few locations that use bright colours in the background or to purposely draw people towards them, such as advertisements or sweets.
Color footage from Lewis Mercer on Vimeo.
The coloured buildings on the street seem to give the area a sense of variety and it makes them all look quite inviting, as while they seem like old styled buildings due to the bright colours they are not too imposing. While the brightly packaged sweets and chocolates seem to try and draw you towards them as an incentive to buy them which shows how colours can affect what people may buy, this is also the case with the small cafe as with it being coloured very brightly it looks like it would have a rather positive atmosphere inside, inviting people in.
OH&S: Occupational Health and Safety
As this was a new area we were filming in there would need to be some precautions as to how we were going to film and where as the area was unfamiliar to us we would need to take extra care when travelling to a location. In this instance it was a rather busy street so we would need to be careful not to get in peoples way or have any of the equipment damaged. some of the risks involved included:
- Risk of falling and causing injury to ourselves/other crew members/ members of the public
- Risk of dropping and/or damaging equipment
- Risk of being mugged/robbed
- Risk of accidentally hitting members of the public with equipment whilst travelling/setting up
- Risk of being hit by traffic
- Risk of getting lost
- Hazards such as objects in the path e.g. broken glass
- Travel in groups between locations
- Do not leave equipment unattended, always have one member watching the equipment at all times
- Share the load of equipment to avoid risk of one person being over encumbered and dropping the equipment
- Ensure that when filming either the camera is set up in an open clearly visible manner that will be easily avoidable by members of the public or the camera is set up in a position that is out of the way and will cause minimal disruption to members of the public
- Ensure that whilst filming all crew members stay clear of the road and traffic to avoid getting hit and injuring themselves
- Ensure that all equipment is safely packed away once filming has been completed and while travelling to different locations
Monday, 15 October 2012
3rd Outing: Tracking Shots
On the 3rd time we went out filming we realised we needed tracking shots that could capture some of the conventions of new wave, so we decided to choose a location that could capture the essence of a social issue affecting the local area such as unemployment. We decided to capture some static tracking shots initially just to determine if the way we were shooting the footage and the location would work out the way we hoped. The footage is new wave in the fact it is filmed in a location that reflects a social issue and we were using only one camera, as we have no budget similar to French New Wave films that are filmed with little or no budget at all.
static tracking shots from Lewis Mercer on Vimeo.
The footage is comprised of shots from two different viewpoints and angles, and I edited it together to give it the appearance of a quick cut, a technique often used in New Wave films, the footage is also shot in high contrast monochrome, another convention of French New Wave, also because the footage was shot in a local area with real peoples reactions to the camera being captured. the footage shows a subject walking through an area that has many rundown shops that have gone out of business to highlight the possible social issue of unemployment in the area.
OH&S: Occupational Health and Safety
During this outing we would be out in public filming shots for our New Wave project and there would be a various amount of safety concerns that we would need to address before we commenced filming as we would be carrying expensive filming equipment and would be in a high traffic area with a large amount of people in the vicinity so we would need to be aware of the various hazard that could occur during the shoot.
static tracking shots from Lewis Mercer on Vimeo.
The footage is comprised of shots from two different viewpoints and angles, and I edited it together to give it the appearance of a quick cut, a technique often used in New Wave films, the footage is also shot in high contrast monochrome, another convention of French New Wave, also because the footage was shot in a local area with real peoples reactions to the camera being captured. the footage shows a subject walking through an area that has many rundown shops that have gone out of business to highlight the possible social issue of unemployment in the area.
OH&S: Occupational Health and Safety
During this outing we would be out in public filming shots for our New Wave project and there would be a various amount of safety concerns that we would need to address before we commenced filming as we would be carrying expensive filming equipment and would be in a high traffic area with a large amount of people in the vicinity so we would need to be aware of the various hazard that could occur during the shoot.
- High volume of traffic that could prove dangerous
- Be aware of the locations reputation e.g. is it known to have high crime rates
- Risk of injury due to falling/dropping equipment/being knocked by passers by/ being hit by traffic/misconduct
- Risk of being hit by traffic as it was a busy area built up area
- Risk of being mugged/robbed
- Risk of dropping/damaging equipment
- Risk of injuring other people through dropping equipment/misconduct
- Always travelling in groups to avoid being mugged/robbed in public
- Share the equipment equally so no one person is over encumbered and risks dropping the equipment and damaging it
- Take caution whilst travelling directly next to the road to avoid falling and being hit by oncoming traffic
- Ensure that the camera and equipment is never left unattended
- Ensure that whilst filming no passers by accidentally knock over or damage any equipment
- Ensure that whilst filming you are in a relatively open area and easily visible to avoid getting in the way of other people trying to get past
- If and wherever possible film from a location that is out of the way and will cause the least disruption to other people around you
- Ensure that all equipment is secured in a safe manner before commencing filming and packed away whilst travelling to a new posit or location
Wednesday, 10 October 2012
2nd Outing: Camera Movements
During the time that we were filming on location for the second time, we decided to take some shots from an escalator to try and get some interesting camera movements, we had a subject go up and down on as set of escalators and had the camera placed either in front of or behind them, to capture the movement of the subject whilst remaining in focus, and to create a simple, interesting tracking shot.
escalator footage from Lewis Mercer on Vimeo.
This technique is considered a New Wave camera movement because it is using innovative use of the environment to create a tracking shot of the subject in an interesting way, and also because this technique requires no other special equipment and simply uses modes of transport already present in the environment to its advantage.
This footage is similar to a scene in Jean-Luc Godard's film "Breathless" where the camera is placed on an escalator facing a woman who is travelling up them which then turns to a tracking shot, so we were trying to recreate that in our footage by using a new wave technique.
escalator footage from Lewis Mercer on Vimeo.
This technique is considered a New Wave camera movement because it is using innovative use of the environment to create a tracking shot of the subject in an interesting way, and also because this technique requires no other special equipment and simply uses modes of transport already present in the environment to its advantage.
This footage is similar to a scene in Jean-Luc Godard's film "Breathless" where the camera is placed on an escalator facing a woman who is travelling up them which then turns to a tracking shot, so we were trying to recreate that in our footage by using a new wave technique.
OH&S: Occupational Health and Safety
During the filming of this scene and while practicing this technique there were a few health and safety concerns that needed to be addressed as both the subject and the person operating the camera would be on a moving platform, and there would be other people around them as they were in a public area. These hazards include:
- Both the subject and camera operator would be on a moving surface and could slip/fall and/or injure others nearby
- They would be holding expensive equipment and would be at risk of damaging it
- Risk of falling on the escalator
- Risk of injuring themselves and/or others
- Behaving appropriately whilst on the escalators
- Ensure that the subject and camera operator are standing firmly on the escalator
- Ensure that either the subject or camera operator has one hand on the railing for support to avoid loss of balance whilst either ascending or descending
- Ensure that no other people are in very close proximity to the subject/ camera operator whilst filming.
- Consider that other people will be around during filming and that crew members should stay a safe distance from them whilst on the escalators.
Tuesday, 9 October 2012
Lighting Examples: Edge
The last lighting technique we attempted was the use of Edge lighting which creates a very high contrast between the light and dark areas of a subject, and exaggerates shadows and has very little highlights or illumination to give the subject an almost sinister, mysterious appearance. We tried to create this lighting by using a small source of light to create a hard lighting effect that would only highlight a small part of the subject while the rest would be cast in shadow, our footage shows how the shadows cover more than half of the subjects face and there is only a small glimmer of light from the subjects eye which makes the subject look almost mysterious.
Edge light ex from Lewis Mercer on Vimeo.
This lighting technique is also used in New Wave films, again because its shot in high contrast monochrome, but also because of the effect it has on the subject, by maxing their features in shadow it creates a mysterious effect on the subject, and makes the subject seem darker, almost more cynical which could be seen in certain new wave films such as Jean luc Godards "Breathless" (1960). These lighting techniques are also new wave because they were low budget films so shots that have lighting that only requires one light source would be easier to film on a small budget.
This is a screenshot from Godards film "Breathless" which shows edge lighting in effect on this character to cover his facial features in shadow.
Edge light ex from Lewis Mercer on Vimeo.
This is a screenshot from Godards film "Breathless" which shows edge lighting in effect on this character to cover his facial features in shadow.
Lighting Examples: Butterfly
Another lighting technique we were to put into practice is "Butterfly" lighting which was often used in Hollywood films of the 50's, its used to flatter the subject and make them more attractive so it would most likely have been used on female subjects. We tried to practice this by also using a female subject and our footage shows how it affects the subjects facial features as it adds shadow under the subjects cheek bones and over their eyes which illuminates the subjects face making it more striking.
Butterfly Light ex from Lewis Mercer on Vimeo.
This footage is also new wave in the fact that it is shot in high contrast monochrome that would be present in many French new wave films of the 1950-60's. The lighting highlight the subjects features in a way that makes them more attractive, which is often present in French new wave films as if there was a female actress as the subject the lighting technique would generally be used to make them look attractive. It is also used because butterfly lighting only requires a main light source which is useful for new wave films since it can be done on a small budget. A vague example of butterfly lighting would be in Jean-Luc Godard's film "Breathless" whenever the female character is on screen.
Butterfly Light ex from Lewis Mercer on Vimeo.
This footage is also new wave in the fact that it is shot in high contrast monochrome that would be present in many French new wave films of the 1950-60's. The lighting highlight the subjects features in a way that makes them more attractive, which is often present in French new wave films as if there was a female actress as the subject the lighting technique would generally be used to make them look attractive. It is also used because butterfly lighting only requires a main light source which is useful for new wave films since it can be done on a small budget. A vague example of butterfly lighting would be in Jean-Luc Godard's film "Breathless" whenever the female character is on screen.
Monday, 8 October 2012
Lighting Examples: Rembrandt
This is our footage of when we attempted to produce the Rembrandt lighting technique, we tried to adjust the brightness of the key light and the position of the reflector to try and discern what effects it had on the images appearance, as well as how effectively we could produce this lighting technique. The way you can determine that this technique is Rembrandt lighting is that half of the subjects face is un-illuminated but has a small triangular piece of light under the subjects eye to highlight their features a small amount.
Rembrandt light ex from Lewis Mercer on Vimeo.
This footage contains elements of new wave as it is shot in high contrast monochrome, much like the films of the French new wave, the lighting used creates a stark contrast between highlights and shadow on the subject, which this technique is often used in French new wave films due to it also only requiring one light source so it is ideal for a small budget. This technique can be seen, if not vaguely in Francois Trauffants film "the 400 Blows", the subjects face is only half illuminated with a small triangle of light on the un-illuminated side.
Rembrandt light ex from Lewis Mercer on Vimeo.
This footage contains elements of new wave as it is shot in high contrast monochrome, much like the films of the French new wave, the lighting used creates a stark contrast between highlights and shadow on the subject, which this technique is often used in French new wave films due to it also only requiring one light source so it is ideal for a small budget. This technique can be seen, if not vaguely in Francois Trauffants film "the 400 Blows", the subjects face is only half illuminated with a small triangle of light on the un-illuminated side.
Thursday, 4 October 2012
Lighting Evaluation
Summary
Through all of the problems that we had to deal with during the process of our lighting session overall we managed to perform the three different lighting techniques:Rembrandt,Edge and Butterfly lighting, and to an extent they went rather well, we managed to pull off these new techniques in order to use them later on in actual film shoots which would improve our footage greatly, especially if we are shooting a new wave film a it requires high contrast lighting such as Rembrandt or Edge. These new techniques we have practiced are going to help us better light our film scenes to improve the overall quality of them.










Through all of the problems that we had to deal with during the process of our lighting session overall we managed to perform the three different lighting techniques:Rembrandt,Edge and Butterfly lighting, and to an extent they went rather well, we managed to pull off these new techniques in order to use them later on in actual film shoots which would improve our footage greatly, especially if we are shooting a new wave film a it requires high contrast lighting such as Rembrandt or Edge. These new techniques we have practiced are going to help us better light our film scenes to improve the overall quality of them.
Lighting Problems
Problems and Technical Faults
During the time we were practicing our development on lighting techniques we came across many problems in the process. To begin with whilst trying to set up the backdrop we had trouble unravelling it, due to its sheer size we had trouble lifting it, and in the end it unravelled on its own onto the floor so we decided to use a large white piece of cloth instead. Another problem we found was that whilst setting up the key light, we had difficulty getting it to work as for a few minutes we had no idea how to turn it on and afterwards we were unsure how to adjust it to the correct amount of light we needed although it was resolved after a while. However yet another problem occurred, this time with the flash trigger attached to the camera, it wasn't connecting to the umbrella light so the flash was not working, this was a major problem as the regular flash on the camera wasn't half as effective as with the flash trigger on the key light. In the end we had to waste at least 25-30 minutes fixing it so we had to work quicker to get the lighting techniques done because of that technical fault, other problems we found included camera batteries running out and gaps in the studio windows so we needed to spend time filling them in to make the room lightproof so as not to ruin the effectiveness of the key light during the shots.
We had a large array of problems during the lighting techniques session which we needed to backtrack and spend time fixing and adjusting, which became annoying as it caused us to stop shooting on a few occasions and even to relocate to a different area because the key light wasn't working. Although eventually all of the problems did get resolved even if through simple means, and we did get all of the lighting techniques completed in the end, which looked appropriate enough for a first attempt as they were new techniques we were testing out.
During the time we were practicing our development on lighting techniques we came across many problems in the process. To begin with whilst trying to set up the backdrop we had trouble unravelling it, due to its sheer size we had trouble lifting it, and in the end it unravelled on its own onto the floor so we decided to use a large white piece of cloth instead. Another problem we found was that whilst setting up the key light, we had difficulty getting it to work as for a few minutes we had no idea how to turn it on and afterwards we were unsure how to adjust it to the correct amount of light we needed although it was resolved after a while. However yet another problem occurred, this time with the flash trigger attached to the camera, it wasn't connecting to the umbrella light so the flash was not working, this was a major problem as the regular flash on the camera wasn't half as effective as with the flash trigger on the key light. In the end we had to waste at least 25-30 minutes fixing it so we had to work quicker to get the lighting techniques done because of that technical fault, other problems we found included camera batteries running out and gaps in the studio windows so we needed to spend time filling them in to make the room lightproof so as not to ruin the effectiveness of the key light during the shots.
We had a large array of problems during the lighting techniques session which we needed to backtrack and spend time fixing and adjusting, which became annoying as it caused us to stop shooting on a few occasions and even to relocate to a different area because the key light wasn't working. Although eventually all of the problems did get resolved even if through simple means, and we did get all of the lighting techniques completed in the end, which looked appropriate enough for a first attempt as they were new techniques we were testing out.
Wednesday, 3 October 2012
Lighting Techniques: Edge
The third lighting technique we were introduced to is edge lighting, it uses hard lighting to cast a lot of shadows over a subjects face to obscure it, making the subject seem sinister, it was used all throughout films like "Sin City". Edge lighting requires very little light to highlight a subject and it creates a very stark contrast between light and shade as less than half of the subject is illuminated while the other is cast in shadow.

These two examples show how the lighting casts shadow on a large proportion of the subjects facial features to create contrast between light and shade, with only a small part of the subject being highlighted.
The technical setup for edge lighting is similar in a way to Rembrandt lighting with small changes including less light being used. Firstly the key light must be placed at a 90 degree angle to the subject and it must be at eye level, the camera must face the subject a 0 degree angle while the subject is turned towards the space between the camera and key light at a 30 degree angle, if a fill light is used it must be at a 70-80 degree angle to the subject on the opposite side to the key light.

These two examples show how the lighting casts shadow on a large proportion of the subjects facial features to create contrast between light and shade, with only a small part of the subject being highlighted.
The technical setup for edge lighting is similar in a way to Rembrandt lighting with small changes including less light being used. Firstly the key light must be placed at a 90 degree angle to the subject and it must be at eye level, the camera must face the subject a 0 degree angle while the subject is turned towards the space between the camera and key light at a 30 degree angle, if a fill light is used it must be at a 70-80 degree angle to the subject on the opposite side to the key light.
![]() |
| Diagram of Edge lighting setup |
Lighting Techniques: Butterfly
Another lighting technique we required practice with is known as Butterfly or Paramount lighting, this type of lighting is used to flatter the subject, by creating shadows above the eyelids and cheekbones, this type of lighting is mainly used in hollywood to make actresses and models look more attractive as it casts more light on the facial features.

The lighting highlights their facial features in clear detail making them stand out, and the shadows under the cheekbones and over the eyelids exaggerates this.
The setup for this style of lighting would require the subject to be facing the camera head on so that all of the face is visible, the key light would need to be behind the camera and at a height of 2-3 ft higher than the subject with it turned at an angle of 70 degrees, there would also be no need for a fill light as the key light would be aimed directly at the subject so a reflector would be impractical.

The lighting highlights their facial features in clear detail making them stand out, and the shadows under the cheekbones and over the eyelids exaggerates this.
The setup for this style of lighting would require the subject to be facing the camera head on so that all of the face is visible, the key light would need to be behind the camera and at a height of 2-3 ft higher than the subject with it turned at an angle of 70 degrees, there would also be no need for a fill light as the key light would be aimed directly at the subject so a reflector would be impractical.
![]() |
| Diagram of Butterfly Lighting setup |
Lighting Techniques: Rembrandt
One of the lighting techniques we were going to practice using is Rembrandt lighting, this type of lighting is uses hard lighting to cast half of a subjects facial features in shadow to provide stark contrast between the light and dark, with a small triangle of light under the subjects eye as a highlight on the un-illuminated side of the subjects face. This technique was named after the Dutch painter Rembrandt van Rijn, whose paintings often showed this use of light.
These images show how rembrandt lighting can be used to create contrast between the light and dark areas on a subjects face, and how the small triangle of light highlights the un-illuminated side.
In order to use the rembrandt lighting technique, the setup of the equipment used is important. First of all the camera must be setup to face straight forward, the key light must be placed at a 40-45 degree angle to the subject and the lights height must be 1-2 ft higher than the subjects head, the subject must then be faced at a 30 degree angle towards the space between the camera and the light source, a fill light such as a reflector must also be used and that should be at a 40-45 degree angle on the opposite side of the key light. All of this preparation was required in the initial setup of our equipment before we could start filming, so it was essential that we placed the key light and camera at the correct height and angles.
![]() |
| A Rembrandt portrait |
![]() |
| Rembrandt lighting |
These images show how rembrandt lighting can be used to create contrast between the light and dark areas on a subjects face, and how the small triangle of light highlights the un-illuminated side.
In order to use the rembrandt lighting technique, the setup of the equipment used is important. First of all the camera must be setup to face straight forward, the key light must be placed at a 40-45 degree angle to the subject and the lights height must be 1-2 ft higher than the subjects head, the subject must then be faced at a 30 degree angle towards the space between the camera and the light source, a fill light such as a reflector must also be used and that should be at a 40-45 degree angle on the opposite side of the key light. All of this preparation was required in the initial setup of our equipment before we could start filming, so it was essential that we placed the key light and camera at the correct height and angles.
![]() |
| Diagram of Rembrandt Lighting setup |
Lighting Setup
2nd October 2012
As part of our new wave project, one of the essential things that we had not yet put into practice was efficient lighting techniques, so we decided to set aside a day where we would practice the different lighting techniques that are used in new wave films. First of all was the initial setup of the lighting equipment and the backdrop, we needed to unfurl the backdrop, setup the umbrella light to use as our key light, setup the tripod and camera, the flash trigger and we needed to organise the positions of the camera and light source to coincide with the different lighting techniques. All of this preparation was vital to ensure that when we got down to actually filming these lighting techniques it worked effectively. The initial setup of the lighting equipment was a new kind of task for us as we hadn't used large lighting equipment before, so at first there were a few uncertainties on how to operate them, however as we were only using one key light, we quickly got accustomed to it. After all of the equipment was setup and ready to use we wanted to make a quick start on practicing the different techniques we might need for later shoots.




When setting up the lighting in the studio one of the things we needed to take into consideration was the health and safety concerns of the studio to ensure the safety of our coworkers, we took into consideration the various hazards and dangers we could face whilst working in this confined area.
Potential hazard(s):
All of the potential hazards listed above all have simple solutions that helped prevent any OH&S concern. To begin with whilst setting up the lighting and backdrop we ensured that all wires and equipment was kept out of the way of any area where any person would be walking. The backdrop was unravelled from its frame until the stands to support it were correctly setup and locked into place, the tripod that held the camera was securely locked into place and kept in a specified area whilst shooting and was not moved from that spot. To avoid any issues with the lighting equipment the subject was directed to not look directly at the light whilst we were utilising the flash and all members were kept clear of the lighting equipment during shooting to avoid injury in case it should fall and/or become hot, also whilst shooting the subject was seated on a stool with both feet placed firmly on the ground to avoid injury via falling. Since we were working in an enclosed space each member was instructed to move carefully when needed and to avoid accidental contact with another person to reduce risk of falling and/or unnecessary obstruction whilst shooting. All of the OH&S concerns we noticed during this shoot were all taken care of in order to avoid unnecessary injury during the session.
These images show our initial setup of the equipment and as we soon found out fixing a backdrop and operating a light all require more than one person simply due to the size of the equipment being used, as we did experience quite a few problems which we needed to correct before we could actually start shooting, so the setup of the equipment proved an interesting task overall.
OH&S: Occupational Health and Safety
When setting up the lighting in the studio one of the things we needed to take into consideration was the health and safety concerns of the studio to ensure the safety of our coworkers, we took into consideration the various hazards and dangers we could face whilst working in this confined area.
Potential hazard(s):
- Stray wires and cables across the floor
- Lighting equipment can become very hot
- Equipment such as tripods could not be correctly locked
- Backdrop stands not setup correctly
- Backdrop could fall from its frame
- Flash from the lights could be harmful if looked at directly
- Subject could fall off the stool provided whilst acting/modelling
- If the camera should become damaged small parts could be scattered across floor
- Studio is an enclosed space so risk of fire is increased
All of the potential hazards listed above all have simple solutions that helped prevent any OH&S concern. To begin with whilst setting up the lighting and backdrop we ensured that all wires and equipment was kept out of the way of any area where any person would be walking. The backdrop was unravelled from its frame until the stands to support it were correctly setup and locked into place, the tripod that held the camera was securely locked into place and kept in a specified area whilst shooting and was not moved from that spot. To avoid any issues with the lighting equipment the subject was directed to not look directly at the light whilst we were utilising the flash and all members were kept clear of the lighting equipment during shooting to avoid injury in case it should fall and/or become hot, also whilst shooting the subject was seated on a stool with both feet placed firmly on the ground to avoid injury via falling. Since we were working in an enclosed space each member was instructed to move carefully when needed and to avoid accidental contact with another person to reduce risk of falling and/or unnecessary obstruction whilst shooting. All of the OH&S concerns we noticed during this shoot were all taken care of in order to avoid unnecessary injury during the session.
Subscribe to:
Posts (Atom)











